TTL Torluftschleier GmbH

Do you have any questions?

  • air recirculation unit for shielding cold rooms or transport paths with high exhaust speed in 2 performance classes, each with 5 construction widths

Build

Industrial air curtains - powerful for robust use

Installation options

Analysing the building situation

To specify the type selection, analyse your building situation and decide which installation variant makes sense.

Which air curtain is suitable for you always depends on the type of building in which the device is to be installed. The corresponding installation principle is then also decided. Taking stock briefly offers some clarity here.
The following building types are defined: 
 

Building type A
The room has door surfaces only on one side of the building and no connection to upper floors, which creates an internal thermal condition

As a rule, an installation according to the STE standard principles is sufficient.

Building type B
In the building, there are room connections to the top through an open extension over several floors. There are escalators, lifts or permanently open corridors, escape routes and staircases.

For this building type, an installation according to the AWE screening roller principle is recommended.

Building type C
Unprotected door surfaces are opposite or around the corner and cause draughts

In addition, the following points must be taken into account when selecting and installing an air curtain system:

  • Pressure situation in the building
  • Alignment of the door to be protected to the main weather direction
  • Door geometry - door dimensions

All basic conditions must be analysed and evaluated. More powerful units should be deliberately chosen for this situation and mounted according to the installation principle AWE or even better according to TWINtec - counter-current principle.

If you need help with the analysis of the building, our field service will be happy to assist you on request.  About the field service
Once the type of building has been determined, the installation occurs with the appropriate variant:

Installation variants

AWE – Abschirmwalzen-Einbau

with air intake above the door and exhaust in the room. Formation of a screening roll whose rotation direction acts against the incoming cold air.

Due to the temperature conditions prevailing in a cooling or cold room - room interior colder than room outside - this type of installation corresponds to a SCREEN ROLL INSTALLATION and offers a significant increase screening performance.

STE – standard installation

An installation according to the standard flow principle is not recommended for the temperature and flow conditions in the door of a cooling or cold room, since in this case the colder room air would be conveyed to the outside at the bottom.

Planning principles

Room area

The larger the volume of the room or building, the greater the dynamic pressure on the building. This dynamic pressure causes a negative pressure, which is reduced above the door area, among other things. This means that there is an undesired exchange of air masses at different temperatures.
 

Exhaust height

The exhaust height is one of the most important criteria when selecting air curtain systems. The lower the unit is mounted above the ground, the smaller the amount of air is required to achieve a sufficient screening effect. In that regard, all architectural and technical possibilities should be taken into consideration. Low air volume means: low heating power, low noise level and low purchase and operating costs.
 

Room height

The room height in connection with the room area gives a characteristic value for the leakage of the room and thus for the design of the air curtain. This also applies in connection with thermal buoyancy.

A larger room area (room volume) generally results in an increase in leakage caused by doors, windows and leaks in the building. This increases the air exchange at the door. Due to these conditions and as a result of practical experience, the inclusion of the room size to be screened has proven itself for the design of air curtain systems.

 

Planungsgrundlagen

 

Control - regulation

TOUCH

Console unit for power control of air curtains according to ambient conditions

SMART module

Module for parallel control of TOUCH functions via mobile phone

SPACS

Control unit for customer-oriented control or regulating tasks

OUR CONTACT PERSONS

Are you interested in a TTL air curtain?

TTL Ansprechpartner
Your personal contact person

Phone:

Fax:

Or send an e-mail

Subscribe to our newsletter now!

Subscribe to our newsletter now and stay up to date.

By submitting your registration, you confirm our data protection regulations.
We will send you an e-mail to confirm your registration.